exorcist instructions - Wargaming Forum and Wargamer Forums
Modelling and Painting Discuss or display anything and everything regarding Terrain, Modelling and Painting here.

LinkBack Thread Tools Display Modes
post #1 of 2 (permalink) Old 12-26-08, 10:26 PM Thread Starter
Senior Member
Dagmire's Avatar
Dagmire's Flag is: United Kingdom
Join Date: Oct 2008
Location: Essex, rayleigh
Posts: 1,668
Reputation: 1

Default exorcist instructions

Well just a quicky to ask if anyone has any or knows of where i can find any. Kira got me the tank for xmas but i cant put it together

Please listen to my PODCAST


Originally Posted by Jaraknarn
This unholy amalgum of womanly sexiness with unfathomable macho should never have been created. Birth rates will plummit, the entire male population will be turned, women kind everywhere will cry desperately to ravished, but no man will heed the call except Dagmire himself. Perhaps this has been Dagmires plan all along. . . . . .
Dagmire is offline  
Sponsored Links
post #2 of 2 (permalink) Old 12-26-08, 10:41 PM
Senior Member
officer kerky's Avatar
officer kerky's Flag is: Australia
Join Date: Jun 2008
Location: australia newcastle
Posts: 1,449
Reputation: 1


found this on putting it together hope its what you wanted

I presume you're asking about the fancy Pipe Organ version with all
the Pewter pieces not the Forge World version with resin pieces.

Test fit all the pewter pieces. They tend to warp. But you already
knew that. :-) Try to find some pictures of assembled Exorcists or
better yet, find one you can look at up close and personal. You
definitely want a better idea of how everything fits together than
just the instructions. Be prepared to use a rubber hammer and a couple
slabs of flat wood to help unwarp some pieces without flattening them.

Glue the back door of the Rhino Chassis SHUT and let it set overnight.
You need all the strength you can get back there with all the weight
of the Pipes centered on the rear section of your tank.

Glue the round Missile Bay (where the Servitor is busy loading) to the
underside of the Exorcist 'roof' as a separate stage so the weight of
the pewter piece doesn't warp the plastic piece. I used Super Glue to
glue the pewter piece in, pressed VERY hard to get it to pop into
place and let it set overnight. I then smeared some 5 minute Epoxy
around the joint on the inside to make certain it will NEVER fall
inside the completed tank. After that set overnight, I glued the roof
on top of the Rhino Chassis and let it set overnight while upside

Use a 5 minute Epoxy to glue the 3 sections of pipes to the horseshoe
shaped piece and each other. Do the same for the podium/keyboard
pieces. This will help fill in the inevitable gaps. Leave the Missile
Rack at the back of the Podium as a separate piece for painting then
use 5 minute Epoxy to glue it in place at the end.

I found the Keyboard a real bear to paint when assembled but didn't
have the skill to paint all the podium pieces separate then Epoxy them
together ESPECIALLY since I wasn't certain how everything was supposed
to go together even when test fitting with bluetack to hold stuff
together while I checked. In the end, I simply smeared some 5 minute
Epoxy on the parts I knew had to touch and relied on the Epoxy to
slowly set while I fiddled with the podium. Eventually, everything
seemed to pop into position. Perhaps you have more skill and will be
able to paint the Keyboard before assembling the Podium.

Glue the Servitor and Musician together but do NOT glue them in place.
Paint them separate. This will also help when painting the inside of
the areas where they'll eventually stand. I even hardcoated them

I painted all the Side and Front panels separately then Super Glued
them in place during final assembly mostly because I didn't want to
mess with trying to paint the edges of each piece. Painting them
separate also allowed me to hold them at weird angles while smearing
paint in all the nooks and cranneys.

Do you want to be able to field your Exorcist as an Immolator and/or a
Rhino? If so, you'll want the back Pipes piece, Servitor, and Podium
piece to be removable If not, consider making the back Pipes piece
removable for ease of transport. If you want your Exorcist to be one
piece at the end, consider pinning the horseshoe piece to the Exorcist
'roof' (after the steps I mentioned earlier) then pinning the pipes to
the horseshoe piece. That SHOULD hold the back end together.

Be prepared to spend a LONG time on your Exorcist. I take about a week
to finish 5 Space Marines. It took me an entire month to finish my
Exorcist and that doesn't count the week I spend filing and pounding
pieces between test fittings. Good Luck. The end result, though, is
worth all the time spent on a spectacular modelD
officer kerky is offline  

  Lower Navigation
Go Back   Wargaming Forum and Wargamer Forums > Hobby > Modelling and Painting

Quick Reply

Register Now

In order to be able to post messages on the Wargaming Forum and Wargamer Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome