Magnetized Land Raider - Wargaming Forum and Wargamer Forums
 
LinkBack Thread Tools Display Modes
post #1 of 7 (permalink) Old 01-09-09, 09:26 PM Thread Starter
Senior Member
 
FeedBot's Avatar
FeedBot's Flag is: England
 
Join Date: Dec 2006
Posts: 910
Magnetized Land Raider

This thing was a beast, but well worth it. Now I have a Redeemer, Crusader, & once I get some more bitz, a standard Land Raider. The only out-of-the-ordinary things I used were the magnets and a 1/8" drill bit for the pinvice. The primary magnet used was the D040A ~ 1/8" Dia x 1/25" Thick from www.amazingmagnets.com. I also used D032A ~ 1/8" Dia x 1/32" Thick magnets for very thin peices or as a gap filler if two magnets didn't touch. All of my magnets come from www.amazingmagnets.com, because you get a free sample pack of magnets everytime you order.















Magnetizing the Sponsons Supports:
The basics: (1) Cut nobs off the sponson support (2) Drill 1/8" hole through center of the sponson support (3) insert two or more 1/25" Thick magnets

More Details: This is where the sponson work begins. The nobs mentioned above are the cylidrical pieces that the guns would attach to. When placing the magnets into the support, using thicker magnets might work a bit better. Just make sure that there are exposed magnets on both sides of the support. If you're short on magnets & only want to use 2, you can fill the center (between the magnets) with green stuff. Make sure that their polarities attract.






Magnetizing the Redeamer Sponsons: The basics: (1) widen the flamer & fuel tank holes with a 1/8" drill bit. (2) attach 1/25" Thick magnets (3) glue the tanks & gun together.

More Details: This is not a scary as it looks. I suggest that you assemble the flamer parts & the fuel tank parts before you drill. After drilling and attaching the magnets, it's time to attach the flamer and the fuel tank with the back peice. MAKE SURE THAT THE POLARITIES OF THE GUN MATCHES THE SUPPORT!!!!






Magnetizing the Redeemer Sponsons: The basics: (1) widen the gun & sensor holes with a 1/8" drill bit. (2) attach 1/25" Thick magnets

More Details: Not much to say here. Drill & attach magnets. Make sure the magnets are attracted to the support.







Magnetizing the Gun Armor Plate: The basics: (1) attach 1/25" thick magnet behind the notch on the flamer(2) drill a 1/8" hole behind the notch in the hurricane bolter so that the magnet sinks in a bit and attach the magnet (3) attach 1/32" thick magnets onto armor plate (4) stack 1/32" thick magnets if there is a gap between the gun & the armor

More Details: This one took a bit more work than I had expected. The redeemer bit was easy. Just glue the magnet behind the notch. I had to use 2 so that it would reach the armor plate's magnet. The hurricane bolter was a bit more complicated. You have to drill a hole so that the magnet sinks in a bit. The reason for this is that the armor plate & the hurricane bolter have no space between them. Make sure to use the 1/32" thick magnets for the armor plates. This will help keep the armor plate from sticking out when it is with the hurricane bolter.













Magnetizing the top hatches: The basics: (1)make an anchor for the hatch with sprue, (2) use the sprue in the hatch to hold the magnet, (3) attach the magnets.

More Details: Let me start by saying that this is not necessary. These hatches will stay in by themselves for the most part, but I'm anal & don't want them falling out.
The first step here is to make something for the magnet to anchor to. I used sprue sections with the knobby bits at the end. This is important to do because the hatch sticks out about an 1/8th inch when in place.
**If you do a bit of planning (unlike myself), you can avoid having to use tweezers to glue in the sprue.






The Second step is the hatch itself. I just keep the sprue that comes in the hatch and clipped off the center circle. This will be where you attach the magnet.






Step three, magnets! I like the 1/32" Thick magnets here. They are less expensive and you don't need a strong hold. I use green stuff & superglue for the bottom magnet. It helps to close the gap between the top & bottom magnet. The hatch magnet is just superglued in. If you accidently cut out the sprue from the hatch, you can use a bit of sprue with greenstuff to make up the distance from the top of the hatch to the bottom magnet.





The Assault Cannon: This guy was a bit tuffer. The bullet-feeds force you to put the magnet directly in the center. Attaching the bottom anchor took two peices of sprue. I had to lower the anchor by adding some plastic card to the knobby bits. This kept the bullet feed from bumping into the anchor. The bit of sprue with the magnet on it is a corner peice that was long enouph to reach the magnet in the Assult Cannon.












Magnetizing the Antenna:
The basics: (1) Cut the anetnna from the base (2) Drill 1/8" hole in each, (3) attach 1/32" Thick magnets

More Details: This is not essential, but you'll be glad you did it when you see everyone else has broken and bent antennas. Start by cutting the antenna from the base and drilling a 1/8" hole in each. Use the 1/32" Thick magnets & be careful to drill in center. I would use the Barrel Drilling Quick Tip technique. Now attach the magnets with a bit of superglue & your done. You now have a break away antenna & have entered the relm of magnet overkill. Welcome to the fold.





Magnetizing the Front Exit: The basics: (1) use sprue for magnet anchor op of the upper door (2) attach magnet to the lower door (3) stack magnets there is to much of a gap

More Details: Let me first say that I am not going to paint the inside because that is where I'm going to keep the extra sponsons and accesopries that I'm not using. Not much to say here other than it's a bit of a pain and stacking the small magnets to fill the gap is really helpful.








Here is a look at the magnets from their site: D040A ~ 1/8" Dia x 1/25" Thick NdFeB Disc Magnet, Ni-Cu-Ni plated.
(1 Item = 85 magnets)

Product Part #: D040A
(Qty: 1 x US$6.80)

D032A ~ 1/8" Dia x 1/32" Thick NdFeB Disc Magnet, Ni-Cu-Ni plated.
(1 Item = 100 magnets)

Product Part #: D032A
(Qty: 1 x US$7.00)




Don't forget to check out Da Rollin Waaagh

Last edited by Cypher871; 08-19-11 at 08:18 AM. Reason: Layout
FeedBot is offline  
Sponsored Links
Advertisement
 
post #2 of 7 (permalink) Old 10-22-09, 12:05 PM
Senior Member
 
heretical by nature's Avatar
heretical by nature's Flag is: Australia
 
Join Date: Sep 2009
Location: Australia-Melbourne
Posts: 260
Reputation: 3
thats sweet i was thinking of doing jsut the same
heretical by nature is offline  
post #3 of 7 (permalink) Old 08-15-11, 05:59 PM
Senior Member
 
kharn_the_blood_god's Avatar
kharn_the_blood_god's Flag is: Denmark
 
Join Date: Aug 2011
Location: Engesvang
Posts: 182
Reputation: 1
i dont magnetize the top weapons but nice tutorial
kharn_the_blood_god is offline  
post #4 of 7 (permalink) Old 10-31-11, 05:37 PM
Senior Member
 
Zer0's Avatar
Zer0's Flag is: United Kingdom
 
Join Date: Jan 2009
Posts: 349
Reputation: 1
Sweet! Wish I'd found this before I'd started building my 'raider. Wonder if I can knife the sponson weapons off and magnetize them now?
Zer0 is offline  
post #5 of 7 (permalink) Old 12-23-11, 03:17 AM
Senior Member
 
Brother Constantine's Avatar
Brother Constantine's Flag is: Canada
 
Join Date: Jun 2008
Location: Canada
Posts: 156
Reputation: 3
I am planning on magnatizing a Land Raider also and I have a question for you....

The Sponson mounts for the Crusader and the LR are different, do you know if the las cannons from the LR kit will fit on the LRC sponson posts or visa vera?

I am the Hammer. I am the sword in His hand. I am the Gauntlet about His fist.


Grey Knights

Wood Elves
Brother Constantine is offline  
post #6 of 7 (permalink) Old 02-22-12, 12:00 AM
Member
 
Metalsiege's Avatar
Metalsiege's Flag is: USA
 
Join Date: Nov 2009
Location: Colorado, USA
Posts: 60
Reputation: 2
Awesome work! Some great work getting magnets into some of the more annoying spots on the LR. I couldn't quite figure out a good way to attach my Assault Cannon and how you did it just solved that problem. I wish I would have came across this post before I forgot about the antenna and put my LR into my carrying case, lol.

+rep for a great tutorial!

Suffer not the alien...
the mutant...
the heretic...
Metalsiege is offline  
post #7 of 7 (permalink) Old 03-14-12, 06:48 PM
Senior Member
 
Jace of Ultramar's Avatar
 
Join Date: Aug 2011
Location: San Antonio, Tx
Posts: 3,868
Reputation: 22


Thank-you for this! I'm getting ready to start building Landraiders and other transports soon and this was overly informative.
Jace of Ultramar is offline  
Reply

  Lower Navigation
Go Back   Wargaming Forum and Wargamer Forums > Hobby > Tutorials > Converting, Modelling and Green Stuff

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Wargaming Forum and Wargamer Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome